How much free RAM memory do I have available on my Linux system? Is there enough free memory to install and run new applications?
In Linux systems, you can use the
free command to get a detailed report on the system’s memory usage.
free command provides information about the total amount of physical and swap memory as well as the free and used memory and swap space in the system.
How to Use the free Command
The syntax for the
free command is as follows:
When used without any option, the
free command will display information about the memory and swap in kibibyte. 1 kibibyte (KiB) is 1024 bytes.
The output will include three lines, a header, one line for the memory and one for the swap:
total used free shared buff/cache available Mem: 8075208 3204964 1310540 551232 3559704 4198340 Swap: 2097148 0 2097148
In older Linux versions, the output may be slightly different.
Here’s what each column mean:
- total - This number represents the total amount of memory that can be used by the applications.
- used - Used memory. It is calculated as:
used = total - free - buffers - cache
- free - Free / Unused memory.
- shared - This column can be ignored as it has no meaning. It is here only for backward compatibility.
- buff/cache - The combined memory used by the kernel buffers and page cache and slabs. /this memory can be reclaimed at any time if needed by the applications. If you want buffers and cache to be displayed in two separate columns use the
- available - An estimate of the amount of memory that is available for starting new applications, without swapping.
Showing Memory Usage in Human Readable Format
As we saw in the example above, by default, the
free command shows the memory information in kibibyte. To view the information in human-readable format (usually megabytes and gigabytes), use the
total used free shared buff/cache available Mem: 487M 219M 54M 4.5M 214M 228M Swap: 1.5G 0B 1.5G
Showing Memory Usage in Other Metrics
free command also allows you to specify the unit in which the memory is measured. Valid options are:
--bytes- Display output in bytes.
--kilo- Display output in kilobytes (1KB = 1000bytes).
--mega- Display output in megabytes.
--giga- Display output in gigabytes.
--tera- Display output in terabytes.
--kibi- Display output in kibibytes. (1KiB = 1024bytes). This is the default unit.
--mebi- Display output in mebibytes.
--gibi- Display output in gibytes.
--tebi- Display output in tebibytes.
--peti- Display output in pebibytes.
--si- Instead of 1024, use powers of 1000. For example
--mebi --siis equal to
For example, to show the output in megabytes you would type:
total used free shared buff/cache available Mem: 8075 4022 233 614 3819 3336 Swap: 2097 0 2097
Showing the Column Totals
To display a line showing the column totals use the
-t option. This will give you a sum of the memory and swap in the total, used and free columns.
free -h -t
total used free shared buff/cache available Mem: 7.7G 3.9G 483M 526M 3.4G 3.2G Swap: 2.0G 0B 2.0G Total: 9.7G 3.9G 2.5G
Continuously Print the Output
To continuously display the memory information on the screen use the
--seconds options followed by a number that specifies the delay.
For example, to print the memory information every five seconds you would run:
free -s 5
free command will continue to display the result until you press
CTRL+C. This is similar to the behavior of the
To display the result for a specific number of times use the
--count option. In the example below the command will print the result ten times:
free -s 5 -c 10
By now you should have a good understanding of how to use and interpret the
free command. To view all available
free command line options type
man free in your terminal.